电子调速器控制器的电磁兼容分析与试验验证

基于辐射发射的形成机理,以某型号电子调速器控制器为目标,利用EMSCAN电磁干扰扫描系统对控制器进行近场辐射测试,总结出一套切实可行的辐射发射分析与试验验证方法.在此基础上,对该型号电子调速器控制器进行了整改设计,并进行了试验验证.结果 表明:基于EM-SCAN系统的分析及整改方法效果明显,缩短了电子产品电磁兼容问题的整改设计周期,并节约了测试成本.     

Experimental study on the propagation characteristics of hydrogen/methane/air premixed flames in a narrow channel

This work is focused on the explosion characteristics of premixed gas containing different volume fractions of hydrogen in a narrow channel (1000 mm × 50 mm × 10 mm) under the circumstance of stoichiometric ratio. The ignition positions were set in the closed end and the middle of the pipeline respectively. The results showed that when the gas was ignited at the pipeline closed end, the propagating flame was tulip structure for different premixed gas. When the hydrogen volume fraction was less than 40%, the flame propagation speed increased significantly with the rise of hydrogen volume fraction, and the overpressure peak also appeared obviously in advance. However, when the volume fraction of hydrogen was more than 40%, the increase of flame propagation speed and the overpressure peak occurrence time varied slightly. Furthermore, when the ignition position was placed in the middle of the pipeline, the flame propagation speed propagating to the opening end was much faster than that propagating to the closing end, and there was no tulip shape when the flame propagates to the opening end. The flame propagating to the closed end appeared tulip shape under the influence of airflow, and high-frequency flame oscillation occurred during the propagation. This work shows that the hydrogen volume fraction and ignition position significantly affected the flame structure, flame front speed, and explosion overpressure.     

Numerical investigation on the effects of reaction orders on the flame propagation dynamic behaviors for premixed gas in a closed tube

In this paper, the premixed flame propagation in a closed tube is surveyed using Computational Fluid Dynamics. The propagation characteristics of premixed flame are obtained coupling a single-step reaction mechanism with a laminar flame model. Three single-step reaction mechanisms are established with different reaction orders for hydrocarbon fuels. This study is to establish a wider range of reaction mechanisms and represent actual experimental conditions better. The numerical simulation results demonstrate that reaction orders can affect the tulip flame development. As the flame spreads, the tulip flame fronts become wrinkled. When the reaction order is 2, there are more wrinkles in the flame front and the degree of wrinkles is more obvious. Reaction orders also affect the flame tip velocity and the flame skirt velocity. The main reason is that laminar flame speeds are significantly different. When the reaction orders are 1.5 and 2, laminar flame speeds are mainly affected by temperature, which respectively increase by about 25% and 75%. When the reaction order is 1, the pressure is crucial for the variation of laminar flame speed. The laminar flame speed decreases by about 33%.     

Experimental study on the effect of diluent gas on H2/CO/air mixture turbulent premixed flame

To study the effects of different diluents on the propagation characteristics of H₂/CO/air mixture turbulent premixed flames, a series of experiments were carried out in a turbulent premixed flame experimental system. The effects of turbulence intensity (0.49–1.31 m/s), dilution gas content (10%, 20%, and 30%), hydrogen fraction (50%, 70%, and 90%), and equivalence ratio (0.6, 0.8, and 1.0) on the turbulent premixed flame were studied. The results show that with the increase in hydrogen fraction or turbulence intensity or equivalence ratio, the S_T and u_t increase at the same radius. Compared with N₂ dilution, CO₂ dilution showed a more obvious inhibition effect on S_T. With the increase of Ka, S_T;35mm/u’ gradually decreased, and the extent of S_T;35mm/u’ decrease gradually became smaller. As the intensity of turbulence increases or the hydrogen fraction increases, the slope of S_T,35mm/u’ with Da/Le gradually decreases. In the turbulence intensity range of this experiment, the u_t,35mm/μ_l under nitrogen dilution condition has a larger floating range. The growth rate of u_t,35mm/μ_l at a low equivalence ratio is significantly higher than that at a high equivalence ratio.     

Flame characteristics of premixed H2-air mixtures explosion venting in a spherical container through a duct

The explosion venting duct can effectively reduce the hazard degree of a gas explosion and conduct the venting energy to the safe area. To investigate the flame quantitative propagation law of explosion venting with a duct, the effects of hydrogen fraction and explosion venting duct length on jet flame propagation characteristics of premixed H₂-air mixtures were analyzed through experiment and simulation. The experiment results under initial conditions of room temperature and 1 atm show that when hydrogen fraction was high enough, part of the unburned hydrogen was mixed with air again to reach an ignitable concentration, resulting in the secondary combustion was easier produced and the duration of the secondary flame increased. With the increase of venting duct length, the flame front distance and propagation velocity increased. Meanwhile, the spatial distribution of pressure field and temperature field, and the propagation process and mechanism of the flame venting with a duct were analyzed using FLUENT software. The variation of the pressure wave and the pressure reflection oscillation law in the explosion venting duct was captured. Therefore, in the industrial explosion venting design with a duct, the hazard caused by the coupling of venting pressure and venting flame under different fractions should be considered comprehensively.     

Infiltrated La0.5Ba0.5CoO3-δ in La0.8Sr0.2Ga0.8Mg0.2O2.8 scaffolds as cathode material for IT-SOFC

The electrochemical response of infiltrated La_0.5Ba_0.5CoO_3-δ (LBC) in porous La_0.8Sr_0.2Ga_0.8Mg_0.2O_2.8 (LSGM) has been investigated. The thermal expansion coefficient (TEC) of the resulting electrode was measured, obtaining α?=?12.5?×?10^?6 K^?1, a value similar to that of LSGM. The polarization resistance (Rp) and the processes involved in the oxygen reduction reaction (ORR) for the new electrode were studied and analyzed through complex impedance spectroscopy measurements as a function of temperature and oxygen partial pressure (pO₂), using a symmetrical cell. The value of Rp for the infiltrated LBC turned out to be lower than that measured for an electrode prepared with a composite LBC-LSGM (1:1?wt%) by an order of magnitude, for the temperature range 750?°C ≤ T?≤?900?°C, and about 5 times lower for the temperature range 450?°C≤ T?≤?650?°C. At 600?°C, the LBC infiltrated cathode exhibits a polarization resistance R_p =?0.22?Ω?cm², in air. The complex impedance spectra show two processes, one identified as low frequency (LF),with a characteristic frequency of 10?Hz, and the other as intermediate frequency (IF), with a range between 0.05 and 2000?Hz. The LF process could be associated to the diffusion of oxygen in the gas phase through the pores of the electrode. Its resistance, R_LF =?0.01?Ωc?m²_, was found to be independent of the temperature and half of that obtained for the LBC composite cathode. On the other hand, the IF process is related to charge transfer at the electrode surface and the electrode-electrolyte interface. The LBC cobaltite infiltrated in the LSGM scaffolds offers an adequate thermal expansion coefficient and good electrocatalytic activity for the ORR.     

Surface sedimentation and adherence of Nano‐SiO2 to improve thermal stability and flame resistance of melamine‐formaldehyde foam via sol‐gel method

Melamine‐formaldehyde foam possesses intrinsic flame retardance; however, relative poor thermal stability and a certain amount of heat release rate restrict its applications in heated environment to a degree. In the present research, sol‐gel method has been adopted to precipitate nano‐SiO₂ particles on the surface of the melamine‐formaldehyde foam's fibers to construct a protective inorganic gel layer. Taking advantages of the shielding effects of the gel layer, the thermal‐oxygen degradation of the foam can be greatly retarded during heating; hence, the thermal stability is remarkably improved, and the flame retardance is further enhanced. In addition, introducing a small amount of membrane‐forming agent in the sol‐gel system can make the depositional nano‐SiO₂ particles well adhered to avoid dusting.     

A methodology for predicting and comparing the full‐scale fire performance of similar materials based on small‐scale testing

Reconstructive fire testing is an important tool used by fire investigators to determine the cause, origin, and progression of a particular fire. Accurate reconstruction of the fire requires the laboratory structure to be outfitted with materials that, in terms of contribution to fire growth, perform similarly to the original materials found at the fire scene. Therefore, a procedure was developed to enable fire investigators to select these replacement materials on the basis of a quantitative assessment of their relative fire performance. This procedure consists of gram‐scale and/or milligram‐scale standard testing accompanied by inverse numerical modeling of these tests, which is used to obtain relevant material properties. A numerical model composed of a detailed pyrolysis submodel and empirical flame heat feedback submodels, which were developed in this study, is subsequently employed to simulate the early stages of the Room Corner Test, which was selected to represent full‐scale material performance. The results of these simulations demonstrate that this procedure can successfully differentiate between fire growth propensities of several commercially available medium density fiberboards.     

Synergistic flame retardant effects of activated carbon and molybdenum oxide in poly(vinyl chloride)

The synergistic effects of activated carbon (AC) and molybdenum oxide (MoO₃) in improving the flame retardancy of poly(vinyl chloride) (PVC) were investigated. The effects of AC, MoO₃ and their mixture with a mass ratio of 1:1 on the flame retardancy and smoke suppression properties of PVC were studied using the limiting oxygen index and cone calorimeter tests. It was found that the flame retardancy of the relatively cheaper AC was slightly weaker than that of MoO₃. In addition, the incorporation of AC and MoO₃ greatly reduced the total heat release and improved smoke suppressant property of PVC composites. When the total content of AC and MoO₃ was 10 phr, PVC/AC/MoO₃ had the lowest peak heat release rate and peak smoke production rate values of 173.80 kW m^?2 and 0.1472 m² s^?1, which represented reductions of 47.3 and 59.9%, respectively, compared with those of PVC. Furthermore, thermogravimetric analysis and gel content tests were used to analyze the flame retardant mechanism of AC and MoO₃, with results showing that AC could promote early crosslinking in PVC. Char residue left after heating at 500 °C was analyzed using scanning electron microscopy and Raman spectroscopy, and the results showed that MoO₃ produced the most compact char, with the smallest and most organized carbonaceous microstructures. © 2017 Society of Chemical Industry